Furniture Planner: Will Your Furniture Fit the Room?
This furniture planner draws your room to scale and lets you drag each piece into place. It flags overlaps, blocked doors and gaps that are too tight to walk through, before you buy anything.
Furniture Planner
Drag a piece to move it. Click it, then use the buttons or the arrow keys to nudge it. Everything is drawn to scale.
- Room area0
- Furniture footprint0
- Open floor0
Gaps are measured between pieces that face each other. Low pieces such as coffee tables use a 14 inch (36 cm) gap. A planning aid only: check real measurements before you buy.
Most people buy the sofa first and find out about the walkway later. A furniture planner flips that order. You draw the room to scale, drop in each piece at its real size, and see whether the layout works before anything is delivered or carried up the stairs.
The furniture planner above is a drag-and-drop floor plan. It flags overlaps, pieces that block a door, and gaps that are too tight to walk through. Every example below uses a 12 ft by 11 ft living room, which is 144 by 132 inches (366 by 335 cm), because that’s the room the tool loads by default.
What Is a Furniture Planner and How Does It Work?
A furniture planner is a scale floor plan where each piece of furniture is a rectangle you can move, so you can check fit and walking space before you buy. It does the tape measure work on screen, where a mistake costs nothing.
This one runs four checks. It tests whether a piece sticks out of the room, whether two pieces overlap, whether a piece sits in a door’s swing, and whether the gap between two facing pieces is smaller than your minimum. The footprint of each piece is its width times its depth.
Take the default room. A sofa (84 by 36 in), a coffee table (48 by 24 in) and a TV stand (60 by 16 in) add up to 5,136 square inches, or 35.7 sq ft. The room is 132 sq ft, so the furniture covers 27% of the floor and 73% stays open.
How Do You Use This Furniture Planner?
Enter the room width and length, add each piece from the list, drag it into place, and read the result panel for problems. If you measure in centimetres, switch the toggle and every field converts.
- Choose inches or centimetres at the top of the tool.
- Type the room width and length, measured wall to wall.
- Set the minimum gap. The default is 30 inches (76 cm), which suits a walkway.
- Pick a piece, press Add, and change its width and depth if your piece is a different size.
- Drag it into place, or click it and use the arrow keys. Press Rotate for a quarter turn.
- Add a Door swing piece wherever a door opens into the room.
Red means a hard problem, such as an overlap, a piece outside the room or a blocked door. Amber means a tight gap. Pieces snap to the walls and to each other’s edges within 3 inches, so lining things up takes a second. If the floor is changing too, work out the quantity first with the flooring calculator.
How Do You Measure a Room and Furniture?
Measure the room wall to wall at floor level, then measure the width, depth and height of every piece at its widest point. The widest point is often the arms, a curved back or a footrest, not the seat.
Rooms are rarely square, so measure each wall at both ends and use the smaller number. Baseboards add roughly half an inch to an inch on each wall, so measure to the face of the baseboard rather than the wall behind it. Mark the position of radiators, vents and sockets, because furniture can’t cover them.
For furniture, use the numbers on the product page and then check them with a tape. A recliner needs its open depth if you’ll sit with the footrest up. A sofa that fits the room can still fail at the front door, so measure the door opening and any turns on the way in as well.
How Much Space Should You Leave Between Furniture?
Leave 30 to 36 inches (76 to 91 cm) for walkways and 14 to 18 inches (36 to 46 cm) between a sofa and its coffee table. These are common design guidelines, and they come from how people actually move and reach.
| Space | Gap to leave | Note |
|---|---|---|
| Main walkway | 36 in (91 cm) | 30 in (76 cm) is the minimum |
| Sofa to coffee table | 14 to 18 in (36 to 46 cm) | Close enough to reach, far enough to step in |
| Behind a sofa used as a path | 24 to 30 in (61 to 76 cm) | Skip if the back is against a wall |
| Beside a bed | 24 in (61 cm) minimum | 30 to 36 in (76 to 91 cm) is comfortable |
| Dining chair to wall | 36 in (91 cm) | 44 in (112 cm) lets people walk behind |
| In front of a dresser | 36 in (91 cm) | Room to open drawers and stand |
The tool uses the same numbers. The minimum gap is 30 inches by default, and a gap drops to 14 inches when one of the two pieces is low, like a coffee table, a side table or a nightstand. Gaps of 2 inches or less count as touching, so a bed pushed against a nightstand isn’t flagged. You can raise or lower the minimum if you want a roomier or a tighter plan.
The ranges exist because comfort differs. A 30 inch path works for one person walking through. A 36 inch path is easier when two people pass or someone carries a laundry basket.
How Do You Plan a Living Room Layout?
Start with the biggest piece, usually the sofa, then place the coffee table 14 to 18 inches in front of it and keep a clear path from the door to the seating. Add the TV stand and side pieces last.
In the default room the sofa sits on the long wall with 3 inches to spare. The coffee table is 18 inches from the sofa, which is inside the 14 to 18 inch range, and 32 inches from the TV stand, so there’s space to walk between them. A 36 inch door swing sits in the corner beside the sofa and stays clear of it, so the tool shows no red and no amber.
Designers often keep seats within about 8 feet (2.4 m) of each other, so people can talk without raising their voices. In a larger room, pull the sofa off the wall and leave 24 to 30 inches behind it if people will walk there. Put at least the front legs of the seating on a rug, and add the rug to the plan as a piece if you want to check its size.
How Do You Plan a Bedroom Layout?
Centre the bed on a wall, leave at least 24 inches on each side you use, and check that the nightstands still fit. The bed is the piece that decides everything else.
A queen bed is 60 by 80 inches and a king is 76 by 80. Add two 24 inch nightstands, and a queen needs 108 inches of wall, so a 120 inch wall leaves 6 inches at each end. A king with the same nightstands is 124 inches wide, which is about 10 ft 4 in, so it needs a wall that long.
Along the sides of the bed, 24 inches is the minimum and 30 to 36 inches feels comfortable. At the foot, 36 inches lets you walk past. A 60 by 18 inch dresser needs about 36 inches in front of it so the drawers open and you can stand. If the numbers don’t work, try a full bed (54 by 75 inches) or turn the bed so the headboard sits on the other wall, and let the tool re-check it.
How Much Room Does a Dining Table Need?
A dining table needs about 36 inches between its edge and the wall or the next piece, so someone can pull out a chair and sit down. If people also need to walk behind the seated guests, allow 44 inches.
For a 6-seat table (72 by 36 inches) with 36 inches all round, the room must be at least 144 by 108 inches, which is 12 by 9 ft. With 44 inches all round, it grows to 160 by 124 inches. A 4-seat table (48 by 36 inches) needs 120 by 108 inches with 36 inches all round.
If the room is shorter than that, push the table against one wall and use a bench on that side. The planner lets you try this and see the gaps change.
How Do Doors and Windows Affect the Layout?
Keep every door swing clear, leave a straight path from the door to the main seat, and don’t block a window you need to open. Doors are the layout rule people forget most often.
Add a Door swing piece, which is 36 by 36 inches by default, and the tool flags any furniture that sits inside it. Change the size if your door is narrower or wider. Draw the path from the door to the far side of the room in your head. If you have to zigzag around furniture to get there, move something.
Tall pieces in front of windows block light and the way to open them. If you’re hanging curtains, leave the rod area free and use the curtain calculator to size the fabric.
How Do You Fit Furniture in a Small Room?
In a small room, choose fewer and slimmer pieces, keep them against the walls, and protect one clear path of at least 30 inches. Every inch of footprint counts.
Swapping an 84 inch sofa for a 60 inch loveseat frees 24 inches along the wall. Two 22 inch side tables take less room than a 48 inch coffee table, and they let you walk through. Try each swap in the tool and watch the open floor percentage rise.
Pieces on legs, with visible floor underneath, feel lighter than pieces that sit flat on the floor. The tool can’t show that, but it will tell you whether the layout works.
Which Mistakes Make a Furniture Layout Fail?
The most common mistake is trusting the catalogue size and the room size, without checking the widest point, the door swing and the route into the house. A plan on paper has to survive real life.
- Forgetting the door swing, or a cabinet door and drawers that open into a path.
- Using the catalogue size without checking the arms, legs or footrest.
- Leaving less than 30 inches for a walkway.
- Pushing every piece against the wall, which pulls the seating apart.
- Ignoring stairs, hallways and turns on the way in.
- Buying before testing a second layout.
Once the layout works, finish the room. The room colour combination guide helps with paint and fabric, and it’s easier to pick colours when you know which pieces will be where.
Further reading: the National Kitchen and Bath Association’s planning guidelines set out clearance and passageway recommendations for kitchens and bathrooms.
FAQs
A furniture planner is a scale floor plan where you place furniture rectangles in a room. It shows whether pieces fit, overlap or leave enough walking space before you buy.
Leave 30 to 36 inches for walkways and 14 to 18 inches between a sofa and coffee table. Behind a sofa that is used as a path, leave 24 to 30 inches.
Place the coffee table 14 to 18 inches (36 to 46 cm) from the sofa. That is close enough to reach a drink and far enough to step in.
Leave at least 24 inches on each side you use, and 30 to 36 inches for comfortable walking. A queen bed with two 24 inch nightstands needs 108 inches of wall.
A 72 by 36 inch table with 36 inches all round needs a room of at least 144 by 108 inches. Allow 44 inches if people must walk behind the chairs.
Yes. Switch to centimetres at the top and every field converts. Room size, piece sizes and gaps all use cm, and the 30 inch gap becomes 76 cm.
Yes. Click a piece and edit its width and depth. Use the real measurements from the product page, because catalogue sizes can leave out arms, legs or an open footrest.
It flags a gap smaller than your minimum between two facing pieces. The default is 30 inches, or 14 inches when one piece is low, like a coffee table. You can change the minimum.